PRECISION RIFLE SOLUTIONS, LLC

We are offering a premier 100% American made sniper cradle for precision shooting at extreme distances.

How to Paint Your Tripod

How to paint your tripod

Here is a tutorial on how I paint the tripods. The following is but a way not the only way.

Tape off the rubber feet and the rubber coated center column tension collar, the paint does not stick to the rubber very well. With a medium Scotch Brite pad or 220 grit sandpaper lightly rough up all surfaces to be painted to include the plastic parts. Do not mess with the ball head itself (we will cover how to get any paint off of it later), and I suggest locking it in place with the QD plate attachment square with the center column. Once everything has been roughed up wipe it all down with a damp cloth to remove any sanding dust. After it has dried completely work the legs in and out to make sure you do not have any dust trapped in the legs, and then wipe the entire tripod down again with a clean dry cloth. Extend the legs all the way out insuring they are at their stops and locked, the center column should be at its lowest height and snugged up with the tension collar.

I bolt the tripod upside down on a piece of plate, large enough to span the top of a large trash can and drilled and tapped with a 1/4"x20 hole, this set up allows me to put it up on a trash can and freedom to work all the way around the tripod without moving it. If unable to work on the tripod upside down just make sure you get inside the legs and paint the leg pivot points. The legs are opened to the first notch but do not push the leg angle locks in, as they should be all the way out to allow paint to completely cover them. Spray several light coats of Krylon Fusion camouflage paint until completely covered, do not go too heavy as it will make the tripod hard to deploy and wear your paint job off much quicker. With it still upside down (and paint completely dry) loosen the center tension column and carefully raise the leg assembly on the center column (or raise the center column if right side up) and snug up the center column tension collar to allow you to paint the rest of the center column. At this point I open the legs so they are almost straight out and unlock the leg section locks leaving them open. Paint all the newly exposed areas of the locks and center column. Once it has dried carefully lock the leg locks back fold the legs to the first notch and turn it right side up and touch up any spots you may have missed with it upside down. Allow the tripod to dry overnight. With a clean dry cloth rub the entire tripod down really well (as if you are trying to polish it) to remove any paint dust. Be careful to not go too heavy with the paint on the center column or it will bind in the leg assembly collar. As for the ball head barely loosen the quarter turn lever and with a twisting motion rotate the ball head within the housing and this will remove any paint on it.

If you want to go with a camo pattern like a multicam pattern I suggest you start with the darkest color first (I use dark brown) and apply spots where you want them not too many just enough to help break up the outline. I use adhesive labels cut into random shapes with no straight edges, lots of curves, ranging in size from ¼” to 1” overall length and width. Place your cut out shapes over the spots you have painted. With your next color I used a lighter green camo paint made by Rustoleum, I again painted spots with some of them overlapping my previous spots allowed them to dry and applied another layer of stickers over these new spots. You can repeat this process for as many colors as you wish. After the brown then green I applied my final coat of tan and let it all dry completely before removing the stickers. Touched up any missed spots and once dried wiped it down. You can also do a really nice digital paint job following the same procedure as above but using the small rectangular price tag labels that are about ¼” by ½”.

Another pattern that can be done relatively easily is apply your dark base coat first and allow to completely dry. With a piece of mesh material like a laundry bag (1/4” holes or there about) lay it over the legs and paint over that with your lighter color/s giving you a spotted pattern that blends pretty well. Cut cardboard templates or real veg can also be used to generate your patterns.

 

Choose a dry warm day and preferably paint in the sunlight to achieve best results. The final result will be a reflection of your prep work, patience, and creativity. Good luck and if you should have any questions please do not hesitate to ask. I will try to do a couple and get some pictures as they progress as examples.

Recent Videos

494 views - 1 comment
427 views - 0 comments
4025 views - 0 comments
4606 views - 0 comments