top of page

Freedom Quick Release Mount 1.0 and 2.0

FQRM 1.0 and 2.0

A DIFFERENT RIFLE SUPPORT OPTION. NOT EVERY 

SHOOTING SITUATION IS A NAIL AND NOT EVERY 

SOLUTION IS A HAMMER.

This piece of kit for the shooter’s toolbox combines our widely popular Freedom Quick Release Mount and our QR plate-s(small) and QR plate-l(large), quick release plate. FQRM 1.0 and 2.0 attaches to a section of Picatinny rail by sliding it onto the rail and then utilizes two hex drive cross bolts through the Pic rail slots to secure it in place. Once in place it allows for the rifle to be attached to the receiver plate on the tripod ball head. Occupying only 4 slots of Picatinny rail and extending less than ¾” below the rail it is not eating up a bunch of real estate. With it being hard mounted on the rail section it does not mean you will be spending time locating and attaching the FQRM 1.0 to your rifle when needed. The use of the FQRM 1.0 and 2.0 attaches the rifle to the tripod allowing the tripod to hold the rifle easing strain on the shooter who may be in position for extended periods of time. Being able to engage and disengage the rifle from the tripod by simply throwing a lever means you can establish a firing position and displace very quickly. Fighting a tripod when having to adjust to the situation is not efficient. This system can also free up a hand or two so that other task may be accomplished in position while maintaining the rifle on target line. Gravity and physics play a unique part in rifles hitting the deck so it is always recommended that you don’t leave the rifle unattended farther than arm’s length away regardless of the tripod support system used. The only way to truly keep a rifle from falling from any support is to ground it. I recommend the rifleman position the FQRM 1.0 just forward of the magazine with just enough clearance to allow magazine changes and not interfere with the operation of the rifle. By placing the rifle at almost a balance point and utilizing the ball head as a fulcrum the shooter can manage recoil and adjust for elevation and windage much easier than farther towards the muzzle of the rifle. Applying side pressures through torqueing the sling and or loading (leaning into) the tripod defeats the structural design of a tripod and creates stresses counter intuitive to fundamentals of marksmanship. Positioning one leg towards the target accomplishes a couple things: One it allows the rifle to return to target line with follow through incident to recoil; Two it allows the shooter to get in a good shooting position between the other two legs. In addition to working as a tripod interface mount the FQRM works as a convenient palm rest and barricade stop.

FQRM 1.0

From a solid piece of billet aluminum and anodized black we have combined our regular FQRM and the Quick Release Plate – small (for use with the “Mini”, “Medium”, and “Large” tripods). The FQRM 1.0 allows the rifle to be hard mounted to the tripod ball head receiver plate. This system can be quickly engaged and disengaged by the throw of the receiver plate lever. The FQRM 1.0 slides onto the rifle fore end and is secured by two hex drive cross bolts. The relief groove cut into the FQRM allows the end user to pry the mount open to accommodate off spec rail sections if it is too tight going onto the rail. Tightening the cross bolts will then secure the FQRM in place. ONLY tighten the mount with enough force to keep the mount from moving.

FQRM 2.0

From a solid piece of billet aluminum and anodized black we have combined our regular FQRM and the Quick Release Plate – large (for use with the XL tripod and AF 1100E grip head). The FQRM 2.0 allows the rifle to be hard mounted to the tripod receiver plate. This system can be quickly engaged and disengaged by the throw of the receiver plate lever. The FQRM 2.0 slides onto the rifle fore end and is secured by two hex drive cross bolts. The relief groove cut into the FQRM allows the end user to pry the mount open to accommodate off spec rail sections if it is too tight going onto the rail. Tightening the cross bolts will then secure the FQRM in place. ONLY tighten the mount with enough force to keep the mount from moving. ick to add text, images, and other content

Pricings, Policies, and Specs

We appreciate your interest in our Sniper Shooting Platform with tripod, please do not hesitate to email us at precisionrifle@yahoo.com, or call us at (281) 541-1549 with any questions you might have.

  • PRICING:
  •  

Residents of Texas will have a 8.75% sales tax added to their order.

Military / LE discount offered with proper identification, contact us for pricing.

Discount available for individual purchases only.

THANK YOU FOR YOUR PURCHASE. Customer satisfaction is our primary concern!

The best thank you from our customer is often times a positive review online. Our business is not just about the products we manufacture and sell. Our business is about the customers we serve. Please do not hesitate to contact us with any questions you may have. If there is ever a problem with products or service please contact us immediately for an opportunity to resolve the problem as quickly as possible to customers satisfaction.

REFUNDS

We will provide refunds for items that have not been used or damaged and are in like new condition less the cost of initial shipping and a 10% restocking fee. Return shipping is the responsibility of the purchaser. The refund will be posted to the original credit card used or sent as a check. Please contact us prior to returning an item to allow for specific return instructions.

WARRANTY

We are proud to provide a LIFETIME (as defined by the user and reasonable use) Warranty, for Precision Rifle Solutions manufactured products, against defects in materials and workmanship for the life of the product. This warranty does not cover component parts or malfunction due to alteration, accident, misuse, or abuse. Please contact us by email at precisionrifle@yahoo.com with any questions you may have. Shipping cost to return warrantied items to us is the responsibility of the purchaser but may be credited back to the purchaser upon return of the repaired or replaced item.

Products we offer, other than those specifically manufactured by Precision Rifle Solutions, are covered by the original manufacture. Please refer to their warranty and repair policy. We will certainly work with the original purchaser to facilitate any issues you may have with these products.

Product specifications for the SSP-1 and SSP-2

(Sniper Shooting Platform):

SSP-1

The SSP-1 will accommodate most standard rifle stocks such as seen on a M40A1, Remington PSS, M40A3, Remington ADL and BDL, it will also fit the AIAE and AIAW stocks.

SSP-2

The SSP-2 is best suited for the wider fore ends found on the McMillan A5, Manners T4, and some of the TRG configurations.

Please request "To scale" Microsoft format printable profile templates of the SSP-1 and SSP-2 via email at precisionrifle@yahoo.com . These templates can be printed, cut out, then measured against your stock to insure a proper fit.

Configurations and Dimensions
SSP-1
SSP-2
Weight of Cradle by itself
7.4 oz.
8 oz.
Medium QD Tripod folded up (collapsed)
16 1/4"
16 1/2"
Medium QD Tripod maximum height
43 3/4"
44"
Medium QD Tripod lowest with center post installed
15"
15 1/4"
Medium QD Tripod lowest with center post removed
7 1/2"
7 3/4"
Weight of Medium QD Tripod with cradle
34.5 oz.
35 oz.
Large QD Tripod folded up (collapsed)
20 3/4"
21"
Large QD Tripod maximum height
63 1/2"
63 3/4"
Large QD Tripod lowest with center post installed
18 1/2"
18 3/4"
Large QD Tripod lowest with center post removed
8"
8 1/4"
Weight of Large QD Tripod with cradle
40.5 oz.
41 oz.

Cradle dimensions are with the padding installed and Cordura cover in place. We only use 1000D Cordura material for our covers to maximize resistance to abrasion, dirt, and fabric degradation over time and exposure. The cradles are constructed of 6061 aluminum for strength and minimal weight. The covers are sewn with Mil-Spec thread for durability and longevity. The covers are available in OD - green, Coyote - brown, Crye MultiCam and black. The cradles are tapped ¼” by 20 to accept attachment to most standard tripods.

Tripods

Tripods are manufactured by SLIK and constructed of quality materials which have proven to be both lightweight and durable. Both the medium and large tripods have a dark, gun metal gray finish. The "XL" and "HD" tripods are finished in a satin black.

Payment options:


Shopping Cart: We accept payment in our shopping cart via Paypal.



Phone Orders: We will be happy to accept your credit card payment over the phone at 281-782-9538.



By Mail: If mailing a check or money order please send to the following address with a detailed description of what you would like to order as well as contact information so that we may confirm the receipt of your payment, and keep you updated as to the shipping status.


PRECISION RIFLE SOLUTIONS

220 E. 6TH STREET

DEER PARK, TX 77536

Shipping: In most cases we ship via the United States Postal Service using Priority Mail with delivery confirmation. We are happy to ship internationally, but please keep in mind that these shipping rates do vary. Please email for a shipping quote. We make every effort to ship as quickly as possible, but please keep in mind that these cradles are custom made, and can take up to two weeks for shipment.

bottom of page